MAN Truck & Bus
Towards 5:15, underground: Matthias Wenzel slips into his green overalls, grabs the pit lamp and his emergency oxygen supply. Then he enters the iron cage and plunges into the depths. Pressure builds in the ears on the journey into the earth's interior, the temperature climbs to around 30 degrees Celsius.
Two minutes later, Wenzel reaches the shaft's fill position 714 metres underground. The 49-year-old has been working here as a large equipment driver for three years. He previously worked as a trucker on the motorways and country roads of Europe. Now his driving territory is a dark track system that extends 14 square kilometres beneath the earth. 125 miners and 70 pieces of large-scale mining equipment and vehicles are deployed here below and above ground. A ventilation system provides the mine with fresh air.
Wenzel opens the gate of the cage and walks to the Teutschenthal shaft's fill position. The light of his pit lamp detects the outline of a MAN TGS with overlying dumper. Shortly after that the trucker sedately sets his vehicle in motion. The speed limit is 30 km/h in this subterranean landscape. Some passages are filled so closely that Wenzel could touch the rock walls from the window with an outstretched arm. He stops at the so-called tipping cellar. Bulk material clatters from above into the dumper. “Soon the truck will no longer shine like new”, says Matthias Wenzel and laughs dryly. “But nobody down here will bite my head off because of a bit of dirt or scratches in the paintwork.” After a 20-minute drive the truck approaches a tipping point. Wenzel uses the automatic sliding plate to push his load from the dumper into a cavity. Then he makes his way back – for the next trip.
Over 75 years miners near Halle an der Saale in Saxony-Anhalt have been extracting rock salt and potash – valuable mineral resources for producing edible salt and fertilizers, for example. Since the beginning of the 1990s, GTS Grube Teutschenthal Sicherungs GmbH has been securing the cavities using suitable industrial mineral waste, so-called offset. This protects the mine against dangerous rock falls, which have already occurred three times in its history.
Truck driver Matthias Wenzel's task is to transport the offset from the shaft to the necessary offset location and unload it there. He drives the route five times per shift. It is 18 kilometres back and forth. His MAN truck was specifically converted for mine use. Although a masterly logistical achievement in transporting the truck underground had to be completed before the driver could sit behind the wheel of the TGS for the first time.
The Gress & Zapp commercial vehicle service team worked meticulously on this task for around five weeks. Workshop fitters disassembled the cab, chassis and superstructure from the already drivable truck into several parts and fixed them onto steel plates. Uwe Müller, Operations Manager at Gress & Zapp, directed the crucial steps aboveground at the GTS Grube Teutschenthal site: a crane lifted the truck parts aloft one after the other. It gently set them down upright on steel plates. Sparks flew for a couple of minutes: a welder spot welded the support structures onto the plates. A forklift truck pushed this into the cage. Descent into the depths. A second crane underground in the mine carefully pulled the truck parts out of the cage. “This transport really did come down to every centimetre”, relieved Operations Manager Uwe Müller tells us afterwards.
Ready for transport The truck only fits into the mine cage in individual parts.
Skilful with tools The company Gress & Zapp is a specialist in transporting trucks into mines.
Precision work The truck parts are carefully removed from the cage.
Destination reached The cab stands underground awaiting the remaining operations.
Reassembled The truck is rebuilt in the mine. The entire process took five weeks.
Under way The mine landscape has many branches. A ventilation system supplies the underground caverns with fresh air.
Working in the dark The MAN TGS is reassembled step by step.
Underground trucker Matthias Wenzel manoeuvring the truck through a tunnel.
Powerful and compact The MAN HydroDrive comes into its own in the mining industry.
THIS TRANSPORT REALLY DID COME DOWN TO EVERY CENTIMETRE.
The truck was then rebuilt underground and approved by T.V. Truck driver Matthias Wenzel was soon able to take his first trip. This is not just a standard TGS, however: the family business for special-purpose vehicle construction run by Toni Maurer fitted the original 360 HP three-axle vehicle with an additional lifting and steerable rear axle. “This makes the truck more agile than a conventional four-axle vehicle. It can therefore manoeuvre better in the narrow sections. It can also now operate with a higher permissible laden weight of 35 metric tons”, explains Managing Director Carl Mason referring to the conversion. Because the truck always drives fully loaded to its destination in the mine, where the offset is unloaded.
The HydroDrive with which the truck was equipped at the factory was another criterion for the Teutschenthal miners in deciding to purchase precisely this vehicle from MAN. The reason is that the hydrostatic auxiliary drive on the front axle lends the truck key benefits. These pay off underground and make deployment there possible in the first place: the HydroDrive truck has a vehicle height of 3.05 metres, namely low enough to navigate the mine tunnels, which are partially only 3.60 metres high. In contrast to conventional all-wheel drives, the HydroDrive does not require any additional ground clearance. It also weighs less, offers more payload and consumes less fuel than an all-wheel-drive truck. Yet the MAN HydroDrive has enough traction to cope with difficult surfaces. Driver Matthias Wenzel confirms: “Some sections have steep uphill and downhill gradients. High ambient humidity makes the surface very slippery. I wouldn't be able to cope without the HydroDrive.”
Underground video recordings Matthias Wenzel driving a MAN HydroDrive truck through the Teutschenthal mine. © Roman Pawlowski
Its off-road capability results in the MAN HydroDrive not just having fans in the mining industry. “It's also suitable for use in gravel pits, on construction sites and for instance in forestry”, explains MAN expert Ralf Melbardis. More than 11,000 vehicles have been sold since 2005. One further modification was required to perfectly equip the truck for its tasks in offset mining: the driver's cab has been sealed with silicone and it received an air filter system. This protects the driver against dust emissions, for example.
The purchase is worthwhile for Thomas von Kalnassy, who is Technical Director at GTS Grube Teutschenthal and responsible for service and maintenance of its vehicle fleet.“This is the second MAN in our fleet. HydroDrive trucks are more efficient for underground transport tasks than conventional mining vehicles”, he says. Thomas von Kalnassy has calculated around ten years of underground service life for the new TGS. The truck will face heavy grind on almost 250 days a year. It will travel around 200 kilometres a day and transport an average load of 25 tons– under driving conditions in the mine that are significantly harder than in normal road use.
Offset mining is set to continue in Teutschenthal for around ten years – until the former mining chambers are completely filled. So Matthias Wenzel and his TGS will be kept busy. A colleague replaces the driver after his eight-hour shift. The HydroDrive truck on the other hand continues on its rounds in the darkness of the offset mine: powerful, agile and tireless.